Speed Controller for RC

HOME > Speed Controller for RC > XARVIS XX mDouble X n

SUB MENU

FAQInstruction Manual

XARVIS XX mDouble X n

For all users aiming for the top The highest model performing high potential in every category.

Features

Equipped with the industry's highest performance FET device (Our research as of December 2019)

E.S.C. is equipped with the highest level element in the FET element that determines the essential performance of E.S.C. Thereby, the control circuit has been brushed up.
The basic performance has been greatly improved, and the torque feeling and high efficiency required by the driver has been obtained.

Equipped with "Battery reverse connection protection circuit" and "Alert LED" for reverse connection.

"XARVIS XX" combines the best output in the RC industry with protection of substrate damage by reverse connection by optimizing the FET circuit.@(Our research as of December 2019) In addition, it is equipped with an "Alert LED" that informs you of the reverse connection.
This function prevents E.S.C.board damage due to reverse connection for about 10 seconds.
This protection function is only effective for ESC circuit board.
This function do not guarantee the protection of Chevalier series, capacitors or external devices.

Equipped with BEC voltage switching (6.0 / 7.4V) function

The output current has been increased in addition to the BEC voltage switching function.
It powerfully drives a 7.4V input compatible high torque servo.

Equipped with two dedicated ACUVANCE cooling fan terminals.@(Including fan for FLEDGE)

Two FAN dedicated terminals are installed to enable simultaneous connection of REY-Storm and FLEDGE.
[REY-Storm / XARVIS exclusive high-speed rotation FAN unit ]
[FLEDGE / Forced air-cooled brushless motor]
iWhen using ACUVANCE FAN, the original performance may not be exhibited by power supply from the BEC terminal of the receiver.j

Rebuilt our original 3D bridge structure design.@(FAN floating installation)

It is a structure that the FAN is installed floating above the E.S.C.
XARVIS adopted this 3D design that realized efficient cooling for the first time in the world.
The X-shaped design on the top of the ESC created an efficient airflow.
Higher cooling performance has been obtained.

New capacitor mounting terminal

A small terminal for capacitors is installed in addition to the battery connection terminal. This makes the soldering work easier.

XARVIS XX original setting data will be added at any time by installing a new program control circuit@yPz

Based on XARVIS, a new unique program control circuit to XARVIS XX is installed.
In addition to the newly installed setting items "torque level / torque end point" and "BEC voltage switching", setting items dedicated to XARVIS XX will be added at any time.

[Torque level]: Adjusting the feeling of acceleration / deceleration torque.
[Torque end point]: The neutral position is the starting point of the effect, and it is an item that determines up to which throttle position the torque level is effective.
Refer to the instruction manual for details.

The torque level and torque end point functions cannot be used or set incorrectly when using our motors before LUXON BS and motors of other manufactures.
In addition, the torque and BEC-related functions are TAO II exclusive setting items when XARVIS XX is released, but we plan to support FUTABA S.BUS compatible transmitters in near future.

Fits wireless and wired communication by TAOU.@yPz

The settings on the XARVIS XX unit can be easily changed using the buttons on the main unit, but the use of TAOU greatly expands the settable items and values and dramatically improves drivability.
Since the LINK terminal mounted on the front of XARVIS XX is used for communication with TAOU, there is no need to replace the RX cable from the receiver. Furthermore, by connecting the LINK terminal and the Brain Unitij via the Air Link Adapterij wireless two-way communication with TAO II is possible.
Brain Unit (TAO II All-in-One Package Accessory or OP-15012)
Air Link Adapter (OP-15065)

Also it fits wireless communication with FUTABA S.BUS compatible transmitter (update required)

If you are using Futaba S.BUS compatible transmitter, you can connect an optional S.BUS adapter (OP-15067) to change setting data using the transmitter screen. Motor speed, ESC temperature, Battery voltage, etc. can be displayed on the transmitter in real time.
Caution: XARVIS XX update is required to perform wireless communication using the transmitter.

  • * Please contact Futaba for compatible transmitters. (The transceiver may need to be updated.)
    The setting data cannot be stored in the transmitter, so please use TAOU for storing and managing the setting data.
  • * When XARVIS XX is updated to support S.BUS, settings can be changed in TAO II and data can be saved, but the data log function by TAO II cannot be used.
  • * Items that can be set by TAOU and items that can be set by a FUTABA S.BUS compatible transmitter may be different.
Supports setting changes by Ne-St

XARVIS dedicated setting controller [Ne-St] can also be used.
A version with setting data suitable for XARVIS XX will be released.

Non-Boost / Non-Turbo status can be viewed with LED

The LED flashes when not using boost / turbo. Compatible with regulations for competitions where the use of these features is restricted.

yPz
Update TAOU to enable communication between TAOU and XARVIS XX
After updating TAO II to XARVIS XX compatible firmware, XARVIS and AIRIA settings can be changed (both wired and wireless), but please note the following.

  • ESetting items added as XARVIS XX exclusive functions, such as torque level related functions and BEC voltage switching functions, do not function when using XARVIS and AIRIA.
  • EThe data log function is available only when using XARVIS XX.
Download manual
Download flowchart and list of set values
Return to top

Product Lineup

At the top of the image will change and you move the mouse pointer to the image.


XARVIS XX BK iBlackj XARVIS XX RD iRedj XARVIS XX PU iPurplej
¥26,500
Return to top

Specifications

Power supply 6.0V`8.5V
Max. continuous/instant current Up to max. current produced by battery
Compatible motors Sensored motor-unrestricted (when boost Aurbo is disabled)
sizes of cables AWG 12
Dimensions W30.5~D35.0~H20.5mm (excluding projection)
Weight (ESC main unit) 47.2g
Regulator for receiver/servo 6.0 / 5A@or@7.4V / 5A
Return to top

List of Accessories

Body 1
Instruction Manual 1
Flexible sensor wire (200mm) 1
RX black wire (200mm) 1
double face tape 2
shrinkage tube for silicon wire 2
Battery connector for large current 2
Return to top

XARVIS XX Update

XARVIS XX allows you to enjoy the latest functions and feelings by updating (updating) the firmware (control program).
First, please refer to here, and when you are ready to update, please update according to the following procedure.

m1nInstall firmware update tool for XARVIS XX on your PC

Acuvance Update Tool Ver.1.0 (Release Date, February 21, 2018) XARVIS XX Download

The update tool is common to XARVIS and AIRIA. This step is not necessary if you have already installed it.

[2] Download the latest firmware for XARVIS XX to your PC

0A.0B.02.00 Ver.1.0 (Release Date, December 27, 2019) XARVIS XX Download

As of December 2019, torque level related functions and BEC output voltage switching functions can only be used with this firmware.

mFUTABA S.BUS system compatible versionn

0A.0C.01.00 Ver.F1.0 (Release Date, December 27, 2019) XARVIS XX Download
  • When changing settings or performing telemetry communication with a FUTABA S.BUS system compatible transmitter, install this firmware on XARVIS XX.
  • Regarding XARVIS XX that has been updated to the version compatible with the S.BUS system, you can change the settings and save data in TAO II as usual, but you cannot use the data logging function with TAO II.
  • Items that can be set by TAOU and items that can be set by a FUTABA S.BUS compatible transmitter may differ.
  • As of December 2019, torque level related functions and BEC output voltage switching functions cannot be used with this firmware.

[3] Start the update tool and execute the firmware installation

The update of XARVIS XX is completed aboveI
Enjoy the latest features and feelingsI
Update XARVIS XX in the same procedure as XARVIS.

Setup manual for update tool

Return to top
Copyright (c) ACUVANCE CORPORATION. All rights reserved.

ACUVANCE CORPORATION
7F-4, SHIN-OSAKA MARUBIRU ANNEX,
1-18-22, HIGASHINAKAJIMA,
HIGASHIYODOGAWA-KU,
OSAKA. 533-0033, JAPAN
FAX +81-6-6379-1190